Structural Steel Rolling Mill Plant

Product Description

• Fly Wheel: 16-17 MT Fitted with Shaft EN - 9, Bearing-2nos. C.I. Brackets - 2 nos. Foundation Slabs
• Pulley: V-Belts Pulley fitted with V-Belts E-Section and Counter Shaft Pulley for Main otor
• Reduction Gear Box: teel Fabricator Body Double Helical Gears, Bearings, Oil Lubricant Systems with Gear oil Tank and Pump with Motor
• Ratio: 1:3.5
• Gear FAce: 560 mm
• Pinion Gear Box: 460 mm P.C.D. Center Steel Fabricator Bod in 4 pcs. helical Gears, Bearings, Oil Lubricant systems. Ger Coupling 4 nos.
• Details of Mill Stands: 18" stands 6 nos, with Rolls, Fiber Chocks with Fiber Bearing, Spinle, C.I. Coupling, Foundation Line etc.
• Stand - 1, 54" Roll Barrel Length
• Stand - 2, 50" Roll Barrel length
• Stand - 3, 42, Roll Barrel Length
• Stand - 4, 36" Roll Barrel Length
• Stand - 5, 36" Roll Barrel length
• Stand - 6, 36" Roll Barrel Length.
• Foundation Centreof Mill Stands (Line to Line centre), 54" (1370 mm)
• Operations By conveyor and Tilting / Shifting / Y - Table etc. complete with Chains with Pulleys, Motors, Panel and push button station
• Cooling Bed Fully Automatic Fabricated in M.S. Girders Channels and Chains
• Motor 1500 HP 735 RPM 433 Volts Slippring Make - Alstom, Year 2005 with water stator, Foundation Lines and T - Bols
• Electrical Panel L.T. Panel fitted with 4 nos. A.C.B. and Starters
• Transformers 2750 KVA 33000/433 Volts Make - Kirlosker, Mfg.
• Sub-Station 33000 Volts Line Complete Electrical fitted and Polls etc.
• Electrical Cables L T Cable for main Motor and other small motors.
• Straightening Machine 400 mm centre fitted with 10 Rolls, Gear box, Motor and starter for MS Angle and Channel
• Re-Heating Furnace
• 16 Ft. x 75 Ft. Double Zone complete with all respect
• Pusher (Mechanical) Reduction Gear Box, wtih Motor, Starter
• jector with gear box, Motor, Starter etc.
• main oil tank 30 K.L. and Small oil tank 3 K.L.
• Chimney, 60 ft. Fabricated in M.S. Plate
• Heating Pumping Unit and Blower, with 60 HP Motor.
• Double Air Pipe Line from Respirator to Smoke chimney
• Workshop fitted with Motors and Starters on each machine
• Lathe Machine 16 Ft. 5 Nos.
• Lathe Machine 12 Ft. 2 Nos.
• Lathe Machine 8 Ft.
• Shaper 32"
• Drill 1.5" (40 mm)
• Hexa and Tool Grinder
• Spare Roll Sets: 41 sizes Approx. of 1-Beam, H-Beam (Girder), Channel, Angle and Flats. The details are as below:
• Channel - 5 sizes
• 150 x 75
• 175 x 75
• 200 x 5
• 250 x 82
• 300 x 90
• I-Beam (Girder) - 4 Sizes
• 150 x 75
• 200 x 100
• 250 x 125
• 300 x 140
• H - Beam (Girder) - 3 sizes
• 200 x 200, 200 x 150, 150 x 150 (for Railway)
• Angle - 20 sizes
• 150 x 150 x 20, 16, 12
• 130 x 130 x 12, 10
• 10 x 10 x 12, 10, 8
• 100 x 100 x 10, 8, 6
• 90 x 90 x 6
• 80 x 80 x 8, 6
• 75 x 75 x 8, 6, 5
• 65  65 x 6, 5
• 65 x 65 x 6, 5
• Flat - 9 Sizes 40, 32, 30, 25, 16, 12, 10, 8, 6 (Up to 400 mm Width)
• Laboratory Complete with U.T.M. Machine
• Crane 2 nos. 5 ton Crane Hoist fitted at V Shape Fabricator Box beam Cabin operator
• Shed 200' x 55' x 28' Main shed + 200' x 42' + 41' x 27' + 41 x 15' + 105' x 35 + 80' x 20' + 40 x 84' = 29757 sq. ft. Covered.
• Open Shed 225' x 24.4' for Dispatch of finish products
• Crane 5 + 5 Ton Capacity Double Hoist fitted at V Shape Fabricator Box Beam, Cabin operator at open shed.
• Store & Spare Daily consumable Equipments
• Location ALLAHABAD (U.P.)